Facebook Link Linkedin Youtube
Facebook Link Linkedin Youtube

CreatBot  PEEK-250

The Best Professional

Ultra-high Temperature 3D printer

  • Printing size：250*250*300mm
  • Nozzle: 480°C
  • Platform: 200°C
  • Chamber: 200°C
  • Water cooling/ Heat isolation system
Check Specs
Get a Quote
"Better quality than the German-made, much cheaper than Europe-price" -- Roland Teo, CEO of Props factory Ltd.

The World's First

desktop high-temperature 3D printer
with a max hot chamber of

200 °C

The World's First

When hot chamber reach to 180°C
The outer surface temperature less than
(after 5 hours heating)

40 °C

The World's First

Raise the hot chamber temp. to 180°C in

20 min

Why 180°C hot chamber is so important?

①180°C ambient temperature is the required temperature for PEEK material to anneal.

Therefore, after the device prints the PEEK model, it can be annealed directly in the device.

    The advantages of doing so are:
  • (1)There is no need to remove the model from the platform to avoid the bottom of the model losing platform adhesion, resulting in the internal stress of the bottom model losing platform restraint, causing the bottom of the model to deform after post-processing.
  • (2)Avoid shutting down and cooling the model to take out the model. There is no exchange of hot and cold environments, which causes the model to have a large temperature difference in a short period of time, and the internal stress is fixed, and it cannot be effectively post-heat treated.
  • (3)After printing, the annealing treatment can be set directly inside the printer without any time delay. For example, it is set in advance to stand in a 180°C environment for 5 hours after printing, and then stand in a 120°C environment for 5 hours to fully anneal the PEEK parts.

①180°C ambient temperature is the required temperature for PEEK material to anneal.

(1)Printing environment temperature requirements: Usually set between 160°C and 200°C to ensure that the material can be fully extruded and bonded and reduce the internal stress after molding to prevent cracking. The recommended ambient temperature is 180°C to improve fluidity, obtain higher combined line strength, and improve heat resistance and chemical corrosion resistance by reducing molding internal stress.

(2)PEI has hygroscopic properties and can cause material degradation. The humidity value is required to be less than 0.02%. The drying conditions are 150°C and 4 hours of drying treatment, and the drying treatment can be carried out directly in the cavity.

(3)PEI materials also usually need to be annealed after molding to eliminate the internal stress generated during the molding process. The advantages of direct annealing are the same as PEEK.

Nozzle temp：385°C
Bed temp：200°C
Chamber temp：90°C
Nozzle temp：385°C
Bed temp：200°C
Chamber temp：120°C
Nozzle temp：385°C
Bed temp：200°C
Chamber temp：150°C
Nozzle temp：385°C
Bed temp：200°C
Chamber temp：180°C

70-80°C is the temperature limit of most circuit boards, motors, belts and other parts. Exceeding this ambient temperature, these parts will break down. Therefore, the temperature of ordinary printers with cavity temperature is at this level.

For an ambient temperature of 180°C-200°C, an aviation-grade heat-insulating sports protective cover is also required. The excellent sports heat-insulating material can completely isolate the air below and above the nozzle, and circulate and replace the hot air gathered in the upper cavity with the hot air in the shell under balanced pressure. Ensure that the external temperature of the shell meets the safety standards for human use.

120°C is the temperature limit of high-temperature motors and belts. At the same time, they need to be well cooled, shielded and heat-insulated or heat-dissipated for circuit parts, and heat-insulated for the cavity.

150°C requires a completely independent cavity closure design and heat-insulation design. In addition to the heat screen and heat-dissipation design for all heat-resistant parts, the long-term durability and heat uniformity of the heating device are also required. And the multi-layer heat insulation design of the equipment shell.

Ultra-high temperature extruder system

Equipped with a double-tooth silicon carbide extruder, it has the characteristics of large torque, super wear resistance, and no step loss. It can print all filaments below 500°C, especially carbon fiber and glass fiber materials.

Water cooling device is necessary, which is the key to smooth printing of high-temperature filament. Hot-end is an Integrated die-casting wear-resistant nozzle, which can be replaced within 30 seconds without removing other parts or screws.

200°C thermally uniform chamber

The special spoiler device allows the hot air in the cavity to circulate 360°, ensuring that the cavity is heated evenly, and the polymer material model is evenly crystallized at any angle and perfectly formed.

Chamber thermal insulation/safety


For the first time, an aviation-grade heat-insulating sports protective cover is used in professional-grade equipment. Through clever design, multi-path heat dissipation, customized high-temperature resistant parts, and the use of multi-layer heat-insulating materials, when the chamber temperature reaches 180°C, the temperature of the front door, top door, screen area, body, and side panel area of the machine is within 40°C, ensuring the safety of users.

High temperature platform 200°C

 Aviation-grade ultra-flat platform + polymer-based coating
Natural flatness 0.05mm
High temperature flatness 0.1mm (cavity temperature 180°C)
No manual or automatic leveling required, avoiding manual leveling or sensor failure in high temperature environments

One-stop annealing function

After the model is printed, there is no need to peel the model from the platform, cool it naturally, or anneal it in the annealing furnace.

You can select the “direct annealing after printing” function for the corresponding material such as PEEK, PEI, etc. on the screen in advance. You can also modify the built-in annealing temperature and time in the settings to achieve one-click annealing.

PEEK-300big_case05
PEEK-300big_case04
PEEK-300big_case03
PEEK-300big_case02
PEEK-300big_case01

Technical Specs

Printing

Build Volume

250*250*300 mm

Print Resolution

0.04mm-0.4mm

Number of Nozzles

Single Extruder

Filament Diameter

1.75 mm

Filament Compatibility

Engineering Plastics:
PLA, ABS, ASA, PC, Nylon, PETG, PVDF,Carbon Fiber；
High temperature Material:
PET-CF, PET-GF, UltraPA, UltraPA-GF, UltraPA-CF, PPSU；
Ultra-performance material:
PEI(ULTEM™Full line), PEEK, PEEK-CF(Carbon fiber), PEEK-GF(glass fiber), PEKK, etc.

Nozzle Diameter

0.4mm (0.3~1.0mm optional)
Electrical

Input Power

200V~240V, 20A

Max. Power

2500W

Screen

7'' full color touch screen, multi-language

Print Method

USB Connectivity/USB Disk
Speed

Best Printing speed

55 mm/s

Max. Printing speed

200 mm/s
Mechanical

Cooling

Air pump cooling & water cooling

Platform

PCB aluminum + PEEK print board

Positioning Precision

X Y axis 0.01mm, Z axis 0.0025mm

Extruder

Directly Drive

Machine Construction

Fully enclosed hot chamber
Temperature

Max. Nozzle Temperature

480℃

Chamber Temperature

200℃
Platform Max. Temperature
200℃
Software

Software Bundle

CreatWare, Simplify 3D, Cura, Slice 3r, etc

Supported File Systems

STL,OBJ,AMF

Operating System

Win7/8/10, MacOS
Special Function

Outage Restored

Save data when power is off

Filament Detection

Pause printing when filament run out

Thermal insulation

Three layer insulation+Active air cooling (Chamber temp. reaches 180 ° C, the external surface temp. is less than 40 ° C)

Doors cooling

Active air cooling

High temperature accessories

High temperature resistance motors, linear rails, belts and circuits to ensure long time high temperature printing.
Size & Weight

Machine Size

630*555*815mm

N.W

120 kg

Quick Links

ENQUIRY FORM

© Copyright 2021 RP3D PRODUCTS. All rights reserved.